Leading 10 usual forklift crashes ， forklift procedure must focus on these matters ！.

Leading 10 usual forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not ignore the forklift at work. If the operation is bad, there will certainly be serious accidents in minutes, and there are many accidents entailing forklifts.

Case 1: The forklift cargo obstructed the chauffeur's sight, and the individual in front could not be found, leading to a rolling mishap.
Instance 2: In order to keep the balance of the forklift when lifting heavy products, the staff members utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight exceeds the allowed size of the path and hangs on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender throughout a turn.
Situation 5: The forklift driver did not see the pedestrian, and the pedestrian did not discover the forklift.
Instance 6: The forklift lifts the employees illegally, the forklift driver does not use the safety belt, the forklift lifter drops and the driver is crushed when the forklift rolls over.
Case 7: The forklift chauffeur did not wear a seat belt and dropped from the vehicle when it surrendered and was squashed.
Forklift procedure must take note of these issues ：.

Beginning.
1. Prior to beginning, observe the surroundings, and after validating that there are no obstacles that impede the security of driving, beep the horn initially and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress (air pressure) gauge need to be risk-free before starting.
3. When the forklift starts with a tons, the vehicle driver should initially validate that the lots is steady and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole must be tilted backward. .
2. Do not raise the fork expensive when driving. When getting in and leaving the work website or while driving, be careful that there will be no barriers overhead. When the tons is traveling, the fork must not be raised expensive, which will certainly impact the security of the forklift. .
3. After discharging, the fork should be decreased to the normal driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal must be issued initially. High-speed sharp turns are prohibited. High-speed sharp turns will trigger the vehicle to lose side stability and topple. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is forbidden to brake instantly while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the web traffic rules in the manufacturing facility and need to maintain a particular safety range from the car in front. .
7. When the forklift is running, the load should remain in the most affordable placement that does not impede the driving, and the gantry should be effectively slanted back. The lots shall not be raised except when stacking or packing. .
8. The height of the tons need to not obstruct the driver's sight. In special conditions, when the product influences the forward vision, drive at a low rate when reversing.
9. It is prohibited to activate the ramp, neither to drive throughout the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a reduced rate when going into the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing duty. .
12. If problems are found, they will certainly be repaired and reported in a prompt fashion, and they will certainly never ever operate with ailments or hide them.

filling and dumping.
1. When fork-loading items, the range in between the two forks must be adjusted as required to make the tons of the two forks well balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or draw. In special conditions, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be stopped with the brake. .
4. The speed of the automobile should be slow-moving and consistent. Take care not to roll the wheels on the dunnage, so as not to extend the rolled things and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the load, and it must be kept in mind that the fork tip should not touch other products or things. The lots ought to be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be slanted onward somewhat when the lots is reduced to permit simple placement of the tons and extraction of the forks. .
6. It is prohibited to fork goods at high speed and hit tough items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and injure individuals. .
8. Overloading is prohibited, and it is restricted to utilize forks to lift personnel to take part in high-altitude operations to prevent high-altitude falling crashes. .
9. It is not enabled to use the brake inertia to slide, place, round or roll items. .
10. It is not enabled to make use of forks to choose, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you need to unload the goods or lower the fork frame.
2. Pull the hand brake handle to dead or depress the hand brake button.
3. The engine is shut off and the power is cut off. (Except for unique situations, such as the driver does not leave the automobile's line of vision and does not go beyond 1 minute).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be examined, and gas, lubricating oil and air conditioning water ought to be added.
2. Examine the security performance of beginning, running and braking.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the operation of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the outside leak needs to also be inspected and the seals need to be replaced in time.

Forklift Safety Operation Specifications.
1. You should examine prior to leaving the vehicle;.
2. When you encounter a person before you during driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the nadir of the freight need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be too sharp to stop the propensity of " cost-free turning";.
6. Running up and down the slope needs to be sluggish and uniform, and no activating the incline is allowed.
7. Do not drive across the gradient. When the gradient is above 10%, the vehicle needs to be driven backwards when going downhill;.
8. When the forklift employees lug the goods and move on, if they encounter large or heavy products and most likely to the motorist's view, they must take the reversing exercise
.
The "Eight Prohibitions" ought to be adhered to in the procedure.
1. Solitary fork procedure is not permitted.
2. It is not permitted to lift the goods for far away driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It Stand-on Electric Pallet Stacker is not allowed to utilize inertia force to grab the goods.
6. It is not permitted to utilize stopping pressure to exile round or Stand-on Electric Pallet Stacker easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Parking is not permitted under the list below conditions.
1. Contours, narrow roads, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the exact same length as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844